Axminster, Bottle Stopper Arbor, #1 MT

If you have turned any of our wine bottle stopper kits, you will appreciate the usefulness of this simple device. After drilling your chosen blank and securing the screw from the kit into it, you simply screw the blank onto the arbor. With tailstock...

Axminster, Lathe Mounted Polishing Mop Arbor, #2 MT

An arbor available with either 1 or 2 Morse taper at one end and a tapered thread on the other for mounting a polishing mop. A hollow recess is provided at the tip so that the tailstock can be brought up to keep the arbor securely in place. The mop can...

Axminster, Light Pull Drive, #2 MT

The light pull drive is a friction drive with steps 1/8"(3.2mm), 1/4"(6.35mm), 3/8"(9.5mm), 1/2"(12.7mm) and 5/8"(16mm). Simply slip the blank onto the drive, bring up the tailstock until the blank is supported by the revolving centre, and away you go...

Axminster, Cone Friction Drive Center, #2 MT

Used in conjunction with the Ring and Centre Point Live Centre, this friction drive is ideal for small spindle turning. As the points on both ends are the same, the timber can be quickly reversed if the grain happens to be running the wrong way. Two...

Axminster, Matched Pair Ring Centers, #2 MT

These matched ring centres are very safe to use if you are a newcomer to woodturning. This is due to the fact that if you experience a dig in, the workpiece will stop rotating but the drive centre can continue to rotate. The drive centre works by...

Axminster, Counterbore Drive Kit, #2 MT

Equipped with a 5/16" (8mm) diameter locating pin, this drive centre is used for accurately locating and driving items such as lamp columns which have already been partly bored through from one end. Where this kit differs from other such centres is that...

Axminster, Pro Drive Center, 5/8" (16mm) Diameter, #2 MT

These centres are safe, secure and offer greater versatility and accuracy than the usual two or four prong drive centres. The centre features a spring loaded, stainless steel centre point and a sharp toothed outer ring which provides the drive. The...

Axminster, Jumbo Drive Center, #2 MT

This somewhat oversize centre is particularly useful when turning large diameter pieces or roughing unbalanced work prior to chucking, as with end grain hollow forms. The principle is that the increased diameter of the drive greatly reduces the risk of...

Axminster, 4 Prong Drive Center, 5/8" Diameter, #2 MT

4 Prong 16mm (5/8") diameter drive centres available in either 1MT or 2MT.Features:4 Prong16mm (5/8") diameter2MTAll sizes in inches are for reference only and are not as accurate as the sizes shown in millimeters. For best accuracy, please measure in...

Axminster, Cone Friction Drive Center, #1 MT

Used in conjunction with the Ring and Centre Point Live Centre, this friction drive is ideal for small spindle turning. As the points on both ends are the same, the timber can be quickly reversed if the grain happens to be running the wrong way. Two...

Axminster, 4 Prong Drive Center, 3/8" Diameter, #2 MT

4 Prong 9.5mm (3/8") diameter drive centres available in either 1MT or 2MT.Features:4 Prong9.5mm (3/8") diameter2MTAll sizes in inches are for reference only and are not as accurate as the sizes shown in millimeters. For best accuracy, please measure in...

Axminster, 4 Prong Drive Center, 5/8" Diameter, #1 MT

4 Prong 16mm (5/8") diameter drive centres available in either 1MT or 2MT.Features:4 Prong16mm (5/8") diameter1MTAll sizes in inches are for reference only and are not as accurate as the sizes shown in millimeters. For best accuracy, please measure in...

Axminster, 4 Prong Drive Center, 3/8" Diameter, #1 MT

4 Prong 9.5mm (3/8") diameter drive centres available in either 1MT or 2MT.Features:4 Prong9.5mm (3/8") diameter1MTAll sizes in inches are for reference only and are not as accurate as the sizes shown in millimeters. For best accuracy, please measure in...

Axminster, 4 Prong Drive Center, 1" Diameter, #2 MT

4 Prong 25mm (1") diameter drive centres available in either 1, 2 or 3MT.Features:4 Prong25mm (1") diameter2MTAll sizes in inches are for reference only and are not as accurate as the sizes shown in millimeters. For best accuracy, please measure in...

Axminster, 4 Prong Drive Center, 1" Diameter, #1 MT

4 Prong 25mm (1") diameter drive centres available in either 1, 2 or 3MT.Features:4 Prong25mm (1") diameter1MTAll sizes in inches are for reference only and are not as accurate as the sizes shown in millimeters. For best accuracy, please measure in...

Axminster, 2 Prong Drive Center, 1" Diameter, #1 MT

2 Prong 25mm (1") diameter drive centre available in either 1MT or 2MT. Used when the spindle ends are not square.Features:2 Prong25mm (1") diameter1MTAll sizes in inches are for reference only and are not as accurate as the sizes shown in millimeters...

Axminster, Pro Drive Center, 7/8" (21mm) Diameter, #2 MT

These centres are safe, secure and offer greater versatility and accuracy than the usual two or four prong drive centres. The centre features a spring loaded, stainless steel centre point and a sharp toothed outer ring which provides the drive. The...

Axminster, Counterbore Drive, #2 MT

Equipped with a 5/16" (8mm) diameter locating pin, these centres are used for accurately locating and driving items such as lamp columns which have already been partly bored through from one end. Where this centre differs from other such centres is that...

Oneway, Modified Cup Drive Center, 3/8 Diameter, #2 MT

Oneway Modified #2 MT safe Driver (3/8)Oneway makes some of the finest lathe accessories for woodturning. They offer a full line of Live Centers, Drive Centers, Tool Rests and Spindle Adapters. They are made in their factory in Stratford,...

Oneway, Spur Drive Center, #1 MT

Oneway #1MT Lathe Drive Spur. Designed for direct mounting to your spindle, spurs are available with #1 or #2 Morse Taper.Oneway makes some of the finest lathe accessories for woodturning. They offer a full line of Live Centers, Drive Centers, Tool...

Oneway, Cup Drive Center, #1 MT

Oneway #1 MT Safe Driver - Cup DriveOneway makes some of the finest lathe accessories for woodturning. They offer a full line of Live Centers, Drive Centers, Tool Rests and Spindle Adapters. They are made in their factory in Stratford,...

Oneway, Screw Chuck, #1 MT

Oneway #1 MT Screw ChuckOneway makes some of the finest lathe accessories for woodturning. They offer a full line of Live Centers, Drive Centers, Tool Rests and Spindle Adapters. They are made in their factory in Stratford, CanadaFeatures:Oneway Model...

Oneway, Screw Chuck, #2 MT

Oneway #2 MT Screw ChuckOneway makes some of the finest lathe accessories for woodturning. They offer a full line of Live Centers, Drive Centers, Tool Rests and Spindle Adapters. They are made in their factory in Stratford, CanadaFeatures:Oneway Model...

Axminster, Bottle Stopper Arbor, #2 MT

If you have turned any of our wine bottle stopper kits, you will appreciate the usefulness of this simple device. After drilling your chosen blank and securing the screw from the kit into it, you simply screw the blank onto the arbor. With tailstock...

Hurricane, Crown Spur Drive Center, 1" Diameter, #2 MT

Hurricane Standard Series 1" Crown Drive Center. The crown drive center is a popular method of driving a workpiece between centers on the lathe. This center is 1" in diameter. It provides a strong grip so you can turn your piece without slipping...

Hurricane, Drive Center Set, #2 MT

Hurricane Standard Series 4 Piece Lathe Drive Center Set. Every woodturner needs a variety of drive and tailstock centers supporting their work when turning "between centers" on the lathe.Features:4 Piece Lathe Drive Center which includes: Two 4 Prong...

Hurricane, 4 Prong Drive Center, 1" Diameter, #2 MT

Hurricane Standard Series 4 Prong Drive Center. The 4 prong drive center is the most common method of driving a workpiece between centers on the lathe. This center is 1" in diameter. It provides a strong grip so you can turn your piece without slipping...

Hurricane, Crown Spur Drive Center, 5/8" Diameter, #2 MT

Hurricane Standard Series 5/8" Crown Drive Center. The crown drive center is a popular method of driving a workpiece between centers on the lathe. This center is 5/8" in diameter and is great for spindle work.Features:Crown Drive Center is a popular...

Hurricane, 4 Prong Drive Center, 5/8" Diameter, #2 MT

Hurricane Standard Series 4 Prong Drive Center. The 4 prong drive center is the most common method of driving a workpiece between centers on the lathe. This center is 5/8" in diameter. It provides a strong grip so you can turn your piece without slipping...

Robust, Cup Drive Center, #2 MT

Robust Cup Style Drive Center - #2MTFeatures:Perfect for safely driving spindles and small bowlsThe tip is adjustable and it is threaded ¾-10 for any accessories you may want to addIf you get a catch, the wood just spins on the centerRobust combines...

Robust, Bowl Drive Attachment for Cup Center

Robust Bowl Drive Attachment for Cup CenterFeatures:Threads onto the Robust Cup Center (sold separately) to drive a bowl blank or large spindle between centersSurprisingly powerful, it also allows the work to spin if you get a catchUnlike a spur drive,...

Robust, Cup Drive Center with Bowl Drive, #2 MT

Robust Cup Center Drive w/ Bowl Drive Combo - 2MTFeatures:The Bowl Drive threads onto the cup center and provides more surface area for driving larger workThe tip is adjustable and it is threaded ¾-10 for any accessories you may want to addWhen properly...

Axminster, Pro Drive Center, 5/8" (16mm) Diameter, #1 MT

These centres are safe, secure and offer greater versatility and accuracy than the usual two or four prong drive centres. The centre features a spring loaded, stainless steel centre point and a sharp toothed outer ring which provides the drive. The...

Axminster, Pro Drive Center, 7/8" (21mm) Diameter, #1 MT

These centres are safe, secure and offer greater versatility and accuracy than the usual two or four prong drive centres. The centre features a spring loaded, stainless steel centre point and a sharp toothed outer ring which provides the drive. The...

Oneway, Spur Drive Center, #2 MT

Oneway #2MT Lathe Drive Spur. Designed for direct mounting to your spindle, spurs are available with #1 or #2 Morse Taper.Oneway makes some of the finest lathe accessories for woodturning. They offer a full line of Live Centers, Drive Centers, Tool...

Oneway, Modified Cup Drive Center, 5/16 Diameter, #2 MT

Oneway Modified #2 MT safe Driver (5/16)Oneway makes some of the finest lathe accessories for woodturning. They offer a full line of Live Centers, Drive Centers, Tool Rests and Spindle Adapters. They are made in their factory in Stratford,...

Oneway, Cup Drive Center, #2 MT

Oneway #2 MT Safe Driver - Cup DriveOneway makes some of the finest lathe accessories for woodturning. They offer a full line of Live Centers, Drive Centers, Tool Rests and Spindle Adapters. They are made in their factory in Stratford,...