Axminster, Faceplate Ring for Type C Dovetail Jaws

Made to match the A, B, C and F dovetail jaws, these rings do away with the need for a separate faceplate on which to mount a bowl blank prior to turning the outside. Simply screw the ring to the chosen blank with woodscrews and expand the dovetail jaws...

Axminster, Chuck Hub, 1 1/4" x 8 TPI Thread

Many turners now own more than one of the Axminster chucks with the jaws of your choice mounted and all set to use. So keep them ready for action with one of the Chuck Hubs threaded to suit your chuck. Screw the Hub to the wall and spin your chuck on to...

Axminster, 4 Prong Drive for Type C Dovetail Jaws, 1" Diameter

The Axminster four prong parallel drive centre has been designed to be used in the central bore of the C jaws fitted to the Evolution, and 100mm Clubman chucks. It has principally been produced for those lathes that do not have a hollow headstock, but...

Axminster, Screw Chuck for Type C Dovetail Jaws

Two replaceable stainless steel parallel screw chucks which fit into either the 62mm recess of the A dovetail jaws, or the internal recess of the 100mm or 114mm C dovetail jaws. Particularly useful for the initial mounting of bowl blanks whilst the...

Axminster, Accessory Mounting Jaws for the SK114 Chuck

These accessory mounting jaws are the latest accessory for the Axminster Evolution SK114 4 1/2" chuck. Manufactured in Axminster, they are a precision fit in the SK114’s jaw slides. An additional set of accessory mounting jaws allows faster jaw changes...

Axminster, Jaw Rack

This simple rack for your chuck jaws helps to keep the jaws organised, stored safely and to hand when needed. It is so much easier to work if your accessories are readily accessible rather than rummaging around in a box. The 4 slots at 80mm centres take...

Axminster, Accessory Mounting Jaws for the SK100 Chuck

These accessory mounting jaws are the latest accessory in the evolution of the Axminster Clubman SK100 4" chuck. Manufactured in Axminster, they are a precision fit in the SK100’s jaw slides. An additional set of accessory mounting jaws allows faster...

Axminster, Accessory Mounting Jaws for the SK80 Chuck

These accessory mounting jaws are the latest accessory in the evolution of the Axminster Clubman SK80 chuck. Manufactured in Axminster, they are a precision fit in the SK80’s jaw slides. An additional set of accessory mounting jaws allows faster jaw...

Axminster, Speed Sizer

Based on an original idea shown to us by Chris Fisher 'The Blind Woodturner', the Speed Sizer revolutionises the job of marking jaw sizes onto a turning blank. This 135mm aluminium template makes marking out for a dovetail jaw completely safe, totally...

Axminster, Faceplate Ring for Type F Dovetail Jaws

Made to match the A, B, C and F dovetail jaws, these rings do away with the need for a separate faceplate on which to mount a bowl blank prior to turning the outside. Simply screw the ring to the chosen blank with woodscrews and expand the dovetail jaws...

Axminster, Screw Chuck for Type A Dovetail Jaws

Two replaceable stainless steel parallel screw chucks which fit into either the 62mm recess of the A dovetail jaws, or the internal recess of the 100mm or 114mm C dovetail jaws. Particularly useful for the initial mounting of bowl blanks whilst the...

Axminster, 25mm O'Donnell Dovetail Jaw Insert

These inserts fit into the 50mm (2") Axminster SK100 4" O’Donnell Dovetail Jaws. Held in place by four cap head screws they are relatively quick to fit. These inserts change the gripping range of the 50mm jaw to that of the 25mm (1") O’Donnell jaw. The...

Axminster, Screw Chuck for SK80 Type C Dovetail Jaws

The SK80 Type C screw chuck is a convenient method for mounting a turning blank onto the lathe without having to remove the chuck. The stepped mounting plate locates securely into the recess of SK80 internal grip. The screw is stainless steel with a deep...

Axminster, Faceplate Ring for SK80 Type C Dovetail Jaws

This faceplate ring has an internal chamfer which matches the dovetail on the 80mm C Jaws. The ring is attached to the timber with woodscrews, placed over the jaws on the chuck and the jaws opened up inside the ring to grip it firmly in place. Using a...

Axminster, 38mm O'Donnell Dovetail Jaw Insert

These inserts fit into the 50mm (2") Axminster SK100 4" O’Donnell Dovetail Jaws. Held in place by four cap head screws they are relatively quick to fit. These inserts change the gripping range of the 50mm jaw to that of the 38mm (1 1/2") O’Donnell jaws. ...

Axminster, Faceplate Ring for Type B Dovetail Jaws

Made to match the A, B, C and F dovetail jaws, these rings do away with the need for a separate faceplate on which to mount a bowl blank prior to turning the outside. Simply screw the ring to the chosen blank with woodscrews and expand the dovetail jaws...

Axminster, Morse Taper for Type C Dovetail Jaws, #2 MT

Available in a 2 Morse taper version, this carrier fits into the C type chuck jaws and enable drive centres or arbors to be mounted without the need to remove the chuck from the lathe. Not suitable for use with longer Evolution type accessory mounting...

Axminster, Screw Chuck Faceplate/Drive for Type C Dovetail Jaws

This is an enhanced version of the popular screw chuck for 100mm (4") and 114mm (4 1/2") C type jaws enabling extra flexibility. A very versatile attachment, it can also be used as a faceplate and drive center. Comes complete with both a large and small...

Axminster, Long Key for Clubman Chuck

When larger work is to be turned it is often difficult to get the key down the side of the piece to tighten or loosen the chuck. To overcome this we have produced a long key to fit the keyed versions of the Clubman's chuck as well as the previous model...

Axminster, Standard Key for Clubman Chuck

When larger work is to be turned it is often difficult to get the key down the side of the piece to tighten or loosen the chuck. To overcome this we have produced a long key to fit the keyed versions of the Clubman's chuck as well as the previous model...

Axminster, Long Chuck Key for the SK114 Chuck

When larger work is to be turned it is often difficult to get the key down the side of the piece to tighten or loosen the chuck. To overcome this Axminster have produced two chuck keys, each 255mm (10") long, one to fit the Super Precision chuck with 8mm...

Axminster, Replacement Small Screw for Wood Screw Chuck

These screws will fit both of the 38mm or 75mm diameter Axminster woodscrew chucks as well as the screw chuck inserts that fit into the C type jaws. They are turned from solid stainless steel, with a special thread form developed for maximum grip in all...

Axminster, Buttons, Inserts and Screws for Button Jaws, Set of 4

This pack of 4 buttons and inserts are for use with all sizes of Axminster Button jaws. The pack includes the necessary fixing screws. Although the rubber buttons are easy on the wood, great care should be taken on bowls with a very fine edge, which can...

Axminster, Stacking Turn Studs for Button Jaws, Pack of 8

Axminster Stacking Turn Studs are a great additional accessory for anyone who already owns either the 250mm or 400mm Axminster button jaws. Offered as an alternative to the rubber buttons as a primary gripping device, they give a really positive grip...

Axminster, Replacement Medium Screw for Wood Screw Chuck

These screws will fit both of the 38mm or 75mm diameter Axminster woodscrew chucks as well as the screw chuck inserts that fit into the C type jaws. They are turned from solid stainless steel, with a special thread form developed for maximum grip in all...

Axminster, Replacement Large Screw for Wood Screw Chuck

These screws will fit both of the 38mm or 75mm diameter Axminster woodscrew chucks as well as the screw chuck inserts that fit into the C type jaws. They are turned from solid stainless steel, with a special thread form developed for maximum grip in all...

Axminster, Chuck Hub, M33 x 3.5mm Thread

Many turners now own more than one of the Axminster chucks with the jaws of your choice mounted and all set to use. So keep them ready for action with one of the Chuck Hubs threaded to suit your chuck. Screw the Hub to the wall and spin your chuck on to...

Axminster, External Safety Jaws

These stepped jaws fit into the chuck in place of the accessory mounting jaws to provide a selection of internal and external parallel gripping surfaces. They are made in Axminster using the latest CNC production methods and are compatible with the...

Axminster, Faceplate Ring for Type A Dovetail Jaws

Made to match the A, B, C and F dovetail jaws, these rings do away with the need for a separate faceplate on which to mount a bowl blank prior to turning the outside. Simply screw the ring to the chosen blank with woodscrews and expand the dovetail jaws...

Axminster, Chuck Removal Spanner

One important lesson for woodturners to learn is not to use the chuck key for removing the chuck from the headstock; doing this can damage the hole in the chuck as well as risk breaking the key. This C spanner has been specially produced for the 100mm...